Also in: Español

Solar and electrical unit converter

Quick conversions for solar and electrical work: watts and horsepower, kWh and BTU, amp-hours and watt-hours, AWG and mm², feet and meters, gallons and liters, pump flow units, and °C and °F.

Power, energy, length, area, volume, flow

Wh
1,000
MWh
0.001
MJ
3.6
BTU
3,412.14
therm
0.034121

Amp-hours ↔ watt-hours

V
Ah
kWh
100 Ah at 12 V
1,200 Wh (1.2 kWh)
5 kWh at 12 V
416.667 Ah

AWG ↔ mm²

mm²
10 AWG
5.26 mm²
6 mm² is nearest to
9 AWG (6.63 mm²)

Nearest by size only. Standard metric and AWG sizes don't line up, so when swapping one for the other, pick the next size up and check its current rating.

Temperature

°F
77
K
298.15

How the conversions work

Each quantity converts through one base unit (W, Wh, m, m², L, L/min): the value is multiplied by its unit's factor to the base, then divided by the target unit's factor. A few conversions are formulas rather than factors:

Wh = Ah × V Ah = Wh ÷ V

°F = °C × 9/5 + 32 K = °C + 273.15

AWG diameter (mm) = 0.127 × 92^((36 − gauge) ÷ 39), area = π/4 × d²

The AWG formula is the standard definition (ASTM B258). For 1/0, 2/0, 3/0 and 4/0, use gauge numbers 0, −1, −2 and −3.

One more that trips people up: peak sun hours and kWh/m²/day are the same number. Sun maps that give daily irradiation in kWh/m² can be used directly as peak sun hours.

Worked examples

  • A 100 Ah, 12 V battery stores 100 × 12 = 1,200 Wh (1.2 kWh). A 100 Ah, 48 V battery stores four times as much: 4.8 kWh.
  • A 1 hp pump delivers about 746 W at the shaft (0.746 kW); the electrical power it draws is higher, because the motor is not 100% efficient.
  • A 10,000 BTU/h air conditioner moves 2.93 kW of heat. Its electrical draw is that divided by its efficiency (COP), often 0.8 to 1 kW.
  • 10 AWG wire is 5.26 mm²; the nearest metric sizes are 4 and 6 mm².
  • A 30 m cable run is 98.4 ft; 1,000 US gallons is 3.785 m³.
  • A panel datasheet's −10°C record low is 14°F; the 25°C test temperature is 77°F.

AWG to mm² table

AWGmm²
142.08
123.31
105.26
88.37
613.30
421.15
233.63
142.41
1/053.48
2/067.43
3/085.03
4/0107.22

Conversion factors used

Power
1 kW= 1,000 W
1 MW= 1,000,000 W
1 hp= 745.69987 W
1 BTU/h= 0.29307107 W
Energy
1 kWh= 1,000 Wh
1 MWh= 1,000,000 Wh
1 MJ= 277.77778 Wh
1 BTU= 0.29307107 Wh
1 therm= 29,307.107 Wh
Length
1 mm= 0.001 m
1 cm= 0.01 m
1 km= 1,000 m
1 in= 0.0254 m
1 ft= 0.3048 m
1 yd= 0.9144 m
1 mi= 1,609.344 m
Area
1 cm²= 0.0001 m²
1 ft²= 0.09290304 m²
1 in²= 0.00064516 m²
1 ha= 10,000 m²
1 acre= 4,046.8564 m²
Volume
1 m³= 1,000 L
1 US gal= 3.7854118 L
1 UK gal= 4.54609 L
1 ft³= 28.316847 L
Water flow
1 L/s= 60 L/min
1 m³/h= 16.666667 L/min
1 m³/day= 0.69444444 L/min
1 US gpm= 3.7854118 L/min

Sizing a cable rather than converting one? Use the wire size calculator. Turning Ah into backup time? Try the battery bank calculator.

Take the design tools with you

The Solar Calibrator app has the sizing tools for the job on site: panel count, battery, string and wire sizing, a live tilt meter, an orientation compass, load audits and quotes, offline.